Air Systems

Paintball Tank Hydro Testing: How to Check Your Tank's Hydro Date & When It Expires

Paintball Tank Hydro Testing: How to Check Your Tank's Hydro Date & When It Expires

If you've owned a paintball air tank for more than a couple of years, you've probably noticed a stamped date somewhere near the neck of the tank and wondered what it actually means. That stamp 's your tank's hydro test date, and once it expires, most fields and pro shops won't legally fill your tank until it's retested or replaced. Here's how to find that date, how often it needs to be renewed, and what your options are once it runs out.

What Is Hydro Testing, and Why Does It Matter?

Hydro testing (short for hydrostatic testing) is a safety inspection required for compressed gas cylinders, including the carbon fiber and aluminum tanks used in paintball. During the test, the tank is filled with water and pressurized well beyond its normal working pressure to confirm the cylinder can still safely hold compressed air without any risk of failure. It's the same basic process used for scuba tanks, fire extinguishers, and other pressure vessels. A compressed air tank that fails under pressure is dangerous, so regulators require proof that it's still structurally sound.

How to Find Your Tank's Hydro Date

Every paintball tank is stamped with its most recent hydro test date, usually near the neck or on the composite wrap just below the valve. The format is typically a month and year, sometimes alongside the testing standard the tank was certified under (you may see markings like DOT, TC, or ISO 11119-2 nearby). If you can't find it or the stamp has worn down and become unreadable, don't guess, treat the tank as needing inspection before you fill it again.

How Often Do Paintball Tanks Need to Be Hydro Tested?

Most modern carbon fiber paintball tanks are built with a 5-year hydro test cycle, meaning they need to be retested (or replaced) every five years from their manufacture or last test date to remain legal to fill. This is the standard you'll see on the spec sheet for most current tanks, including popular options from Ninja and HK Army. Aluminum tanks can follow similar cycles but are worth double-checking individually, since the exact interval depends on the certification standard stamped on your specific tank. When in doubt, the stamped date and standard on the tank itself is the deciding factor.

What Happens When a Tank's Hydro Date Expires?

Once a tank's hydro date passes, reputable fields and pro shops won't fill it. This isn't a formality, it's a liability and safety issue, and no shop that values its equipment or its customers will risk filling an out-of-date cylinder. If you show up to a field with an expired tank, expect to be turned away or offered a fill on a rental tank instead, so it's worth checking your date well before game day rather than finding out at the fill station.

Getting Your Tank Hydro Tested or Replaced

If your tank is otherwise in good shape and you'd rather retest than replace it, a paintball pro shop or a facility equipped to service compressed gas cylinders can handle the inspection. It's also a good time to have your regulator checked, since a tank and its regulator tend to see the same wear and tear over the years. For a lot of players, though, an expired tank is also a good excuse to upgrade. Tank technology has moved quickly over the past several years, and today's lightweight compressed air tanks offer better efficiency and lower weight than tanks from even five or six years ago, all while starting their own fresh 5-year hydro cycle. 

Final Fill-Up

Checking your tank's hydro date takes ten seconds and can save you a wasted trip to the field. Make it part of your pre-season gear check alongside your mask, hopper, and marker maintenance, and you'll never be the person standing at the fill station wondering why the shop won't top off your air. If your paintball air tank is about to expire or if you’re just looking for an upgrade, browse our full lineup of paintball tanks and accessories to compare the best selection of paintball equipment on the internet!

Read more
How to Rebuild a Planet Eclipse Geo Reg (Step-by-Step Guide)

How to Rebuild a Planet Eclipse Geo Reg (Step-by-Step Guide)

The regulator is the heart of your Planet Eclipse Geo's air system, and when it starts delivering inconsistent pressure, leaking, or drifting off your velocity, a rebuild is usually the fix. The good news is that rebuilding a Geo reg is a very doable job for a careful owner with the right spares. This guide walks through the process from teardown to chrono, so you can get your marker shooting smooth and consistent again.

Important safety note: always fully degas your marker before you begin. Remove the air tank and make sure all stored gas is discharged. Never disassemble a pressurized marker, and never point it at anyone or look down the barrel during service. Keep your specific model's manual handy.

Before You Start: Gather Your Tools and Parts

A rebuild goes smoothly when you're not scrambling for supplies mid-job. Have on hand a clean microfiber cloth, paintball-safe marker grease, and a set of exact-size replacement O-rings for your regulator. A proper O-ring and seal kit made for your marker is the single most useful thing to keep in your kit, since a rebuild is only as good as the seals you put back in. Work over a clean surface (a tech mat is ideal) so small parts don't wander off or pick up grit.

Step 1: Disassembly and Cleaning

With the marker fully degassed, you can begin the teardown.

Unscrew the reg bottom. Remove the lower reg assembly, or take the assembly out from the frame following your specific model's manual instructions. Different Geo versions vary here, so let the manual guide you.

Pull out the internals. Carefully extract the spring stack, the shim arrangement, and the regulator piston. Pay close attention to the order and orientation of everything as it comes out, because it all needs to go back exactly as it was.

Wipe away old grease. Using a clean microfiber cloth, clean all the old paint, dirt, and thick, gummy grease off the piston and the inner housing. Old, contaminated grease is a common cause of sluggish or inconsistent reg behavior, so get everything clean.

Inspect the seals. Check the internal O-rings on the piston and the top adjuster assembly closely. Look for flat spots, tears, nicks, or any deformation. A worn O-ring here is very often the culprit behind a leak or pressure creep.

Step 2: Reassembly and Lubrication

This is where attention to detail pays off, especially with grease placement.

Replace the O-rings. Swap out any damaged O-rings with exact-size replacements from your spares kit. Even if an O-ring looks only slightly worn, replacing it during a rebuild is cheap insurance.

Lubricate lightly. Apply a thin layer of marker lubrication to the dynamic O-rings on the piston, the ones that move and need to slide smoothly. Thin and even is the goal, not a heavy coating.

Keep the sealing face dry. This is the step people get wrong. Leave the actual flat sealing face, or seat, of the piston completely free of grease. That flat surface needs to seal air metal-to-metal (or against the seat), and grease there prevents it from sealing effectively. Grease the dynamic O-rings, keep the flat seal dry.

Stack the internals in order. Reinsert the springs and shims in their exact original order and orientation back into the regulator body. This is why you noted the arrangement during teardown. The shim stack sets your baseline pressure, so getting it back correctly matters.

Step 3: Resetting and Testing

With everything reassembled, you'll set a safe baseline and then dial in your velocity.

Reset the adjuster. Turn the adjustment screw all the way counterclockwise until it stops. This is the fully out, minimum-pressure position, and it gives you a known starting point.

Set a baseline. Turn the adjuster back inward (clockwise) roughly 3.5 to 4.5 turns as a starting point, depending on your specific Geo model version. This gets you into a safe ballpark before you ever put gas to it. Because the exact figure varies by model, check your manual or ask a tech for your specific gun.

Chronograph and tune. Re-attach your air tank safely and test-fire over a chronograph. Adjust the reg in small increments to bring your velocity to your field's limit (commonly around 280 fps, but always follow local field rules). Never skip the chrono step, since firing without confirming a safe, legal velocity is both against the rules and unsafe.

When to Take It to a Tech

A reg rebuild is approachable, but it isn't for everyone or every situation. If you're not comfortable tracking the shim and spring order, if the reg still leaks or creeps after a careful rebuild, or if you suspect damage beyond the O-rings, hand it to a professional. A botched reg job can cost you far more than the service would have.

A Note on Your Specific Model

Geo regulators differ across versions (Geo 3, 3.5, 4, CSR, and others), and the exact number of adjuster turns and O-ring sizes can vary between them. Always confirm the specifics against your model's official manual before you rely on any baseline number, and keep the correct spares kit for your exact marker.

The Bottom Line

Rebuilding a Planet Eclipse Geo reg comes down to degassing safely, tearing down carefully while noting part order, cleaning thoroughly, replacing and greasing O-rings correctly (dynamic seals greased, flat sealing face dry), restacking springs and shims exactly, and resetting and chronoing before you play. Do it methodically and you'll restore the smooth, consistent air delivery the Geo is known for. Need seals, parts, or a hand? Browse Lone Wolf Paintball's O-ring and seal kits and Planet Eclipse parts and accessories to keep your marker dialed in.

Read more

Powerhouse Featherweight Air System | The Lightest Air Tanks?

Tony shows off the Infamous line of Pro DNA Universal Tank Case and Regulator Cases. First off you can see...
Read more

Top 6 Questions About Paintball Air Tanks

Tony answers the top 5, questions we receive the most, about paintball air tanks...
Read more

Infamous Paintball Tank Case & Regulator Case Review

Tony shows off the Infamous line of Pro DNA Universal Tank Case and Regulator Cases. First off you can see...
Read more